mirror of
https://github.com/KevinMidboe/Arduino.git
synced 2025-10-29 17:40:11 +00:00
84 lines
3.1 KiB
C
Executable File
84 lines
3.1 KiB
C
Executable File
#ifndef config_h
|
|
#define config_h
|
|
|
|
// ===== DISPLAY LIBRARY ===== //
|
|
#include <Wire.h>
|
|
#include <SPI.h>
|
|
#include "SH1106Wire.h"
|
|
#include "SSD1306Wire.h"
|
|
#include "SH1106Spi.h"
|
|
#include "SSD1306Spi.h"
|
|
// =========================== //
|
|
|
|
//#define DEFAULT_SSID "pwned"
|
|
//#define HIGHLIGHT_LED 16
|
|
|
|
// ===================== LED CONFIG ==================== //
|
|
/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
|
|
Uncomment the type of LED you're using
|
|
Only one of them can be defined at a time!
|
|
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
|
|
#define DIGITAL_LED
|
|
//#define RGB_LED
|
|
//#define NEOPIXEL_LED
|
|
|
|
/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
|
|
Adjust following settings for your type of LED
|
|
you can ignore the rest of the #define's
|
|
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
|
|
|
|
// === Settings for Digital LED and RGB LED === //
|
|
#define LED_ANODE false // common vcc (+)
|
|
#define LED_PIN_R 16 // NodeMCU on-board LED
|
|
#define LED_PIN_G 255 // 255 = LED disabled
|
|
#define LED_PIN_B 2 // ESP-12 LED
|
|
|
|
// === Settings for RGB LED and Neopixel LED === //
|
|
#define LED_MODE_BRIGHTNESS 10 // brightness of LED modes
|
|
|
|
// === Settings for Neopixel LED === //
|
|
#define LED_NEOPIXEL_NUM 1
|
|
#define LED_NEOPIXEL_PIN 15
|
|
#define LED_NEOPIXEL_MODE NEO_GRB + NEO_KHZ800
|
|
// NEO_KHZ800 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
|
|
// NEO_KHZ400 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
|
|
// NEO_GRB Pixels are wired for GRB bitstream (most NeoPixel products)
|
|
// NEO_RGB Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
|
|
// NEO_RGBW Pixels are wired for RGBW bitstream (NeoPixel RGBW products)
|
|
|
|
// ===================== DISPLAY CONFIG ==================== //
|
|
#define USE_DISPLAY false // default display setting
|
|
|
|
/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
|
|
Adjust the pins to match your setup
|
|
Comment out the buttons you don't use.
|
|
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
|
|
#define BUTTON_UP 14
|
|
#define BUTTON_DOWN 12
|
|
#define BUTTON_A 13
|
|
|
|
//#define BUTTON_LEFT 12
|
|
//#define BUTTON_RIGHT 13
|
|
//#define BUTTON_B 10
|
|
|
|
/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
|
|
Uncomment the type of display you're using
|
|
Only one of them can be defined at a time!
|
|
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
|
|
*/
|
|
#define DEAUTHER_DISPLAY SSD1306Wire display = SSD1306Wire(0x3c, 5, 4); // for 0.96" OLED
|
|
//#define DEAUTHER_DISPLAY SH1106Wire display = SH1106Wire(0x3c, 5, 4); // for 1.3" OLED
|
|
|
|
/* RST = GPIO 5 (D1)
|
|
DC = GPIO 4 (D2)
|
|
CS = GPIO 15 (D8) or GND
|
|
SCK/SCL = GPIO 14 (D5)
|
|
SDA/MOSI = GPIO 13 (D7) */
|
|
//#define DEAUTHER_DISPLAY SSD1306Spi display = SSD1306Spi(5, 4, 15); // for 0.96" OLED with SPI
|
|
//#define DEAUTHER_DISPLAY SH1106Spi display = SH1106Spi(5, 4, 15); // for 1.3" OLED with SPI
|
|
|
|
//#define FLIP_DIPLAY // uncomment that to flip the display vertically
|
|
// ========================================================= //
|
|
|
|
#endif
|