Update readme w/ architecture, installation and setup

README.md

@@ -1 +1,121 @@
-# hivemonitor-esp32-firmware
+# Hivemonitor ESP32 Firmware
+
+Firmware for running Hivemonitor on ESP32 microcontrollers.
+
+# Architecture
+
+![hivemonitor architecture drawing](https://github.com/KevinMidboe/hivemonitor-esp32-firmware/assets/2287769/c40512e5-9f31-4aea-a8db-e92646c51903)
+
+Complemetary hivemonitor repositories:
+- [Hive monitor webpage](https://github.com/kevinmidboe/hivemonitor)
+- [Hive monitor ESP32 PCB design](https://github.com/kevinmidboe/hivemonitor-pcb)
+
+# Operating modes
+
+## Setup mode
+Both types of devices acting as `sending` and `gateway` have a operating and setup mode. By using the on-board switch labeled "MODE" the esp32 will boot up in setup mode and be available as a WiFi hotspot named `ESP-AP-*`. View [setup section](#setup) below.
+
+## Sender device
+Devices acting as sensor have weight, temperature and humidity sensors connected that will be read and broadcasted using ESP-NOW peer-to-peer protocol. 
+
+## Gateway device
+Device acting as receiver will be simultaneously be listening for messages broadcasted to it's MAC address using ESP-NOW & connected to WiFi to send MQTT messages to a broker. 
+
+# Installation
+
+Clone repository and navigate into folder:
+```bash
+git clone https://github.com/kevinmidboe/hivemonitor-esp32-firmware
+cd hivemonitor-esp32-firmware
+```
+
+## TL;DR
+
+Flash microcontroller:
+```bash
+wget https://raw.githubusercontent.com/glenn20/micropython-espnow-images/main/20230427-v1.20.0-espnow-2-gcc4c716f6/firmware-esp32-GENERIC.bin > firmware-esp32-espnow.bin
+make flash file=firmware-esp32-espnow.bin device=/dev/tty.usbserial-02899247
+```
+Upload source code:
+```bash
+make sender device=/dev/tty.usbserial-02899247
+# or
+make gateway device=/dev/tty.usbserial-02899247
+```
+
+## Flashing firmware
+The current supported flashing tool for micropython firmware is esptool.py. You can find this tool here: https://github.com/espressif/esptool/, or install it using pip:
+
+```bash
+pip install esptool
+```
+
+Download firmware from [supported firmware linked below](#firmware-sources) or compile required micropython with libraries listed below:
+- espnow
+- usocket
+- umqtt.simple
+
+Plug esp32 into computers USB and find it's connected TTY port with:
+
+```bash
+ls -l /dev/tty.*
+```
+
+Erase the existing firmware and then deploy the new firmware using:
+```bash
+make flash device=/dev/tty.usbserial-02899247
+```
+
+## Uploading application source files
+
+For uploading source files we can use adafruit ampy CLI found at https://github.com/espressif/esptool, or installed with pip:
+
+```bash
+pip install adafruit-ampy
+```
+
+Upload all files for ESP32 that will be acting as a `gateway` by running:
+
+```bash
+make gateway
+```
+
+Upload all files for ESP32 that will be acting as a `sensor reader & sender` by running:
+
+```bash
+make sender
+```
+
+# Setup
+
+After uploading source files, use the on-board MODE switch to side marked "Setup" device to boot board into setup mode. Inputs will b based on if device is setup as `sender` or `gateway`.
+
+After setting mode switch and resetting the controller will be discoverable as a WiFi access point serving a configuration page.
+ 1. Connect to WiFi network prefixed with `ESP-AP-`
+ 2. Open browser to http://192.168.0.4
+
+Below shows screenshots of gateway device in setup mode:
+
+![Hive monitor setup site, 3 pages](https://github.com/KevinMidboe/hivemonitor-esp32-firmware/assets/2287769/3e80fa3d-7b5e-4296-89a0-a3d42351ddf3)
+
+🎉 Setup completed!  
+When both a sender and gateway is setup MQTT messages should start reaching broker.
+
+# ESP32
+
+## Deep sleep
+asdf
+
+## Networking
+There are two WiFi interfaces, STA mode is workstation mode (ESP32 is connected to the router)，AP mode provides access services (other devices connected to ESP32).
+
+
+The ESP32 does not have two antennas, but we can run two interfaces `STA` & `AP`. The drawback of this is that since we only have one antenna we need to make sure the sending and receiving devices are both broadcasting on same channel. In a sitation where your WiFi access point might be brodcasting on channel e.g. 6 the ESP32 connects over WiFi on this channel. The ESP32 sending sensor data therefor needs to be broadcasting data over ESP-NOW on same channel.
+
+## Firmware sources
+
+| mpy version | espnow | mqtt* | socket | source                                                                                                                                                                  |
+|-------------|--------|-------|--------|-------------------------------------------------------------------------------------------------------------------------------------------------------------------------|
+| v1.20       | ✅    | ✅   | ✅    | [github.com/glenn20/micropython-espnow/20230427-v1.20.0-espnow/firmware.bin](https://github.com/glenn20/micropython-espnow-images/blob/main/20230427-v1.20.0-espnow-2-gcc4c716f6/firmware-esp32-GENERIC.bin) |
+| v1.19       | ✅    | ✅   | ✅    | [github.com/glenn20/micropython-espnow/20220709-v1.19.1-espnow/firmware.bin](https://github.com/glenn20/micropython-espnow-images/blob/main/20220709_espnow-g20-v1.19.1-espnow-6-g44f65965b/firmware-esp32-GENERIC.bin) |
+