Init commit with many years of arduino sketches and projects. I dont know if the esp8266 includes much, but there are also libraries. I hope they dont have crazy automatic versioning through the Arduino IDE.

enp8266/esp8266_deauther-master/configs/Default/A_config.h

@@ -0,0 +1,83 @@
+#ifndef config_h
+#define config_h
+
+// ===== DISPLAY LIBRARY ===== //
+#include <Wire.h>
+#include <SPI.h>
+#include "SH1106Wire.h"
+#include "SSD1306Wire.h"
+#include "SH1106Spi.h"
+#include "SSD1306Spi.h"
+// =========================== //
+
+//#define DEFAULT_SSID "pwned"
+//#define HIGHLIGHT_LED 16
+
+// ===================== LED CONFIG ==================== //
+/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
+    Uncomment the type of LED  you're using
+    Only one of them can be defined at a time!
+   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
+#define DIGITAL_LED
+//#define RGB_LED
+//#define NEOPIXEL_LED
+
+/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
+    Adjust following settings for your type of LED
+    you can ignore the rest of the #define's
+   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
+   
+// === Settings for Digital LED and RGB LED === //
+#define LED_ANODE false   // common vcc (+)
+#define LED_PIN_R 16      // NodeMCU on-board LED
+#define LED_PIN_G 255     // 255 = LED disabled
+#define LED_PIN_B 2       // ESP-12 LED
+
+// === Settings for RGB LED and Neopixel LED === //
+#define LED_MODE_BRIGHTNESS 10 // brightness of LED modes 
+
+// === Settings for Neopixel LED === //
+#define LED_NEOPIXEL_NUM 1
+#define LED_NEOPIXEL_PIN 15
+#define LED_NEOPIXEL_MODE NEO_GRB + NEO_KHZ800
+//   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
+//   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
+//   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products)
+//   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
+//   NEO_RGBW    Pixels are wired for RGBW bitstream (NeoPixel RGBW products)
+
+// ===================== DISPLAY CONFIG ==================== //
+#define USE_DISPLAY false // default display setting
+
+/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
+    Adjust the pins to match your setup
+    Comment out the buttons you don't use.
+   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
+#define BUTTON_UP 14
+#define BUTTON_DOWN 12
+#define BUTTON_A 13
+
+//#define BUTTON_LEFT 12
+//#define BUTTON_RIGHT 13
+//#define BUTTON_B 10
+
+/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
+    Uncomment the type of display you're using
+    Only one of them can be defined at a time!
+   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
+*/
+#define DEAUTHER_DISPLAY SSD1306Wire display = SSD1306Wire(0x3c, 5, 4); // for 0.96" OLED
+//#define DEAUTHER_DISPLAY SH1106Wire display = SH1106Wire(0x3c, 5, 4); // for 1.3" OLED
+
+/*  RST = GPIO 5 (D1)
+    DC = GPIO 4 (D2)
+    CS = GPIO 15 (D8) or GND
+    SCK/SCL = GPIO 14 (D5)
+    SDA/MOSI = GPIO 13 (D7) */
+//#define DEAUTHER_DISPLAY SSD1306Spi display = SSD1306Spi display = SSD1306Spi(5, 4, 15); // for 0.96" OLED with SPI
+//#define DEAUTHER_DISPLAY SH1106Spi display = SH1106Spi(5, 4, 15); // for 1.3" OLED with SPI
+
+//#define FLIP_DIPLAY // uncomment that to flip the display vertically
+// ========================================================= //
+
+#endif